• Narrow construction for installation on surfaces with limited space
• Integrated keypad
• Mount on a flat surface or a single-gang wall box
• Wiegand-out port for compatibility with most Access Control panels
• Supported card types include HID & ZKAccess 125 kHz proximity cards
• IP67 weatherproof and tamper-proof

• 2 Year Warranty

• Provides all I/O needed for twoadditional doors
• Two dedicated reader inputs
• Four relay outputs
• Four programmable inputs
• For use with X1100 Door Controller only
• Connect up to 16 expansion modules per expansion port, up to 31 expansion modules total
• Scan-to-add card format and serial detection
• Control doors and manage users from the Alarm.com app
• Integrated Alarm.com intrusion and video offerings
• User-friendly, flexible scheduling
• Configure hardware using webor app for easy installation
• Plug & play installation—no networking expertise required

• Nominal 220VAC (range 198VAC - 256VAC) 50/60Hz rated @ 1.2A.
• Power supply input options:
  • a) One (1) common power input for ACM8 and lock power (factory installed).
  • b) Two (2) isolated power inputs - One (1) to power the ACM8 and one (1) for lock accessory power, (external power supply is required). (Current is determined by the power supply connected, not to exceed a maximum of 10A total).
• Eight (8) Access Control System trigger inputs.
• Input options:
  • a) Eight (8) normally open (NO) inputs.
  • b) Eight (8) open collector inputs.
  • c) Any combination of the above.
• 12VDC or 24VDC @ 6A supply current.
• Eight (8) independently controlled outputs.
• Output options:
  • a) Eight (8) Fail-Safe and/or Fail-Secure power outputs.
  • b) Eight (8) form “C” 5A rated relay outputs.
  • c) Any combination of the above.
• Eight (8) auxiliary power outputs (unswitched).
• Fuses are rated @ 3.5A.
• Filtered and electronically regulated outputs (built-in power supply).
• Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
• Fire Alarm disconnect input options:
  • a) Normally open (NO) or normally closed (NC) dry contact input.
  • b) Polarity reversal input from FACP signaling circuit.
• Alarm output relay indicates that FACP input is triggered (form “C” contact rated @ 1A 28VDC).
• Short circuit and thermal overload protection.
• AC fail supervision (form “C” contact).
• Red LEDs indicate outputs are triggered (relays energized).
• Green LED indicates FACP disconnect is triggered.
• AC input and DC output LED indicators.
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when AC fails.
• Zero voltage drop when unit switches over to battery backup (AC failure condition).
• Battery fail and battery presence supervision (form “C” contact).
• Operating Temperature: 0ºC to 49ºC (32ºF to 120ºF).
• Storage Temperature: - 20ºC to 70ºC ( - 4ºF to 158ºF).
• Relative Humidity: 85% +/- 5%.

• Designed for professional access control systems
• Durable, built to withstand years of use
• Pocket-sized device is compatible with many brands of card readers
• Easily attaches to a key ring, badge clip, or lanyard

Space-saving and highly compatible, Akuvox R20K is a compact SIP video doorphone with a numeric keypad. It is typically used in apartment and office buildings.

• 3 Year Warranty

• 120VAC Input, 60Hz, 3.5A.
• Input fuse: 5A/250V.
• Sixteen (16) fuse protected outputs.
• Outputs are rated @ 2.5A.
• 12VDC @ 10.0A supply current.
• Auxiliary Power-Limited output rated @ 1A (unswitched).
• Over Voltage Protection.
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption.
• AC fail supervision (form “C” contacts).
• Notification trigger is selectable for 30 seconds (factory set) or 2 hours.
• Battery fail & presence supervision (form “C” contacts).
• Low power shutdown. Shuts down DC output terminals if battery voltage drops below 71-73% (depending on the power supply). Prevents deep battery discharge.
• Supervised Fire Alarm disconnect (latching or non-latching) 10K EOL resistor. Operates on a normally open (NO) or normally closed (NC) trigger.
• Operating Temperature: 0° C to 49° C (32° F to 120° F).
• Storage Temperature: - 20° C to 70° C ( - 4° F to 158° F).
• Relative Humidity 85% +/- 5%.
• BTU/Hr (approx.): 61 BTU/Hr.
• System AC input VA requirement: 420VA.
• Green AC Power LED indicates 120VAC present.
• AC input and DC output LED indicators.
• Short circuit and overload protection.
• Unit is complete with power supply, enclosure, battery leads and cam lock.

• Single-door controller: Perfect for adding a single door to your access control system.
• Advanced Security: ProdataKey Red products lead the industry in secure communication protocols. This includes OSDP, mobile, and encrypted credential communication.
• Power Monitoring: Equipped with an on-board power supply, and a fully-supervised power circuit that monitors input, output, battery voltage, and overall controller health.
• Plug-and-Play Connectivity: All PDK Red devices were designed to be plug n' play. That means they're easy to install right out of the box. It's simple to add any device, no matter how large the job is.
• Self-Discoverable: The Red 1 will be automatically discovered by the Cloud Node when an Ethernet cable is connected; it is not necessary to enter the IP address; the device is self-discoverable.
• Module Kits: Additional WiMAC and PoE++ plug-and-play connection kits can be added by purchasing the respective wireless or PoE kit. Plug the module into the PDK Red 1 board, and it's ready to go.
• System Scalability: Whether you need one door or a thousand, the PDK Red 1 Controller gives you the flexibility to add more doors anytime, anywhere, on any device.

• 1-5 Year Warranty

• Excellent performance with Android 9.0 system;
• 7-inch capacitive touch screen with energy saving mode
• Ultimate visual experience with 1280 x 800 resolution
• Reception of a HD picture from the door communicator
• Two-way audio communication with other units in the network
• Complies with SIP standard for easy integration in every SIP capable PBXes
• Powered by PoE or external source

• 2 Year Warranty

• Keypad
• High-Security(13.56 MHz)
• Read Range 125 kHz up to 4”
• Output OSDP and Wiegand protocol
• Encryption MIFARE® DESFire® EV2
• Cable Distance Wiegand 500’ (22AWG)
• Protection Rating IP55
• Power 5 - 16V DC (Linear power supply recommended)
• Enclosure Dimensions: 3.25” x 5.1” x 0.71”

• 1-5 Year Warranty

• ZKTeco Smart-Card Proximity Reader
• With Bluetooth functionality, you can unlock you door with your smart phone
• Supports 13.56 MHz contactless smart-cards and 2.4GHz Bluetooth Low Energy
• IP67 weatherproof rated
• Built-in Wiegand-out port
• Single-gang and mullion mounting adapters

• 1 Year Warranty